Smoking area near here

Summary of how to use Wiz2 and troubleshooting problems when they occur

Summary of how to use Wiz2 and troubleshooting problems when they occur Ploom
Ploom PloomX Review PloomX980 yen PloomX Mobius PloomX Camel PloomX CouponIncluding PR

⚡ 【早見表】ウィズ2(with 2)の吸い方のコツ・リセット方法・「すぐ壊れる」と感じた時の対処

※メーカー公式発表・財務省認可価格(2026年10月1日改定反映)と、編集部の整理・過去取材記録を区別して記載しています。

検索されている疑問・確認項目結論・公式基準(2026年10月時点)
吸い方のコツ(味が出ない・薄い時)ボタン操作不要の自動加熱式ですが、強く短く吸うより「ゆっくり長めに吸い込む」とカートリッジ蒸気がたばこカプセルを通りやすくなります。
How to reset Wiz 2動作が不安定な時は、マウスピースを外した状態で本体ボタンを約7〜8秒間(点滅が変わるまで)長押しして再起動を試します。
「すぐ壊れる・吸えない」主な原因カプセル交換時のリキッド結露(液漏れ)が端子部に付着しているケースが多いため、端子とマウスピース内部を乾いた綿棒で拭き取ってください。

Good evening,Heated cigarette blogger Genki (@MOQLOG_JP)It is.

It has been a few days since the pre-sale began,JT's new Wiz 2I'm sure you all have already gotten your hands on one.

This article summarizes how to use each operation with a 10-second video for those who do not know how to use it.

In the latter half of the report, we will also introduce troubleshooting methods to deal with possible malfunctions and failures.

WRITER / Author

Heated Cigarette Blogger

One of the largest heated tobacco and e-cigarette bloggers in Japan, he operates "MOQLOG" (MOQLOG). One of Japan's leading heated cigarette bloggers, he started his operation in March 2016, and as an expert on heated and e-cigarettes that are replacing paper cigarettes, he provides a variety of information on cigarettes.

assistance in news gathering:oricon news Weekly Playboy (lessening the significance or value of the previous word) the likes of

How to use with2 (with2)

A quick look at the areas of concern

The Whiz 2 is compared to the Plumtec Plus Whiz,Button operation and display readability have been greatly improved, making it extremely easy to use.

The button operation is very simple and can be found in the instruction manual, but we have taken each part in a video of less than 10 seconds for your reference.

What to prepare

·Wiz 2 Main unit
·tobacco capsule

Basic operation of Wiz 2

Basic operation of Wiz 2

Operation of the Wiz 2 is simple and easy: just set the cigarette capsule and cartridge and smoke.

When you smoke, it is an auto puff with no button operation, so when you are done preparing, just suck and smoke.

So, here we will explain "Preparation before sucking" and how to operate other than sucking.

How to use Wiz 2 [Quick Reference].

Power ON / OFFNone.
Lock ON / OFF... Click the button 3 times within 2 seconds
mode switchingPress and hold button
Cigarette capsule exchangePress and hold the button for 2 seconds.
Cartridge Replacement... replaced after 5 capsules are smoked.
situation check...One light click of the button

There are only two button operations in Wiz 2: long press and three presses.

How to smoke Wiz 2 (the whole process)

The basic smoking method is a 3-step process, but in addition to this, there are other methods for replacing the "cigarette capsule" and the "cartridge".

Wiz 2 Sucking Procedure

The following is a summary of the operations you need to know for each step of the process.

Please click on the link to jump to the explanation part, so if you want to know only a part of it, please use the links in the page.

How to use Wiz 2 (1) How to insert a cigarette capsule

First, open the "cigarette capsule" and insert it into the insertion port of the Wiz 2.

I don't think you can go wrong with the orientation,Insert the colored ring on top.

How to use Wiz 2 (2) How to set the liquid cartridge

In Wiz 2, the cartridge is now set from the bottom, and the capsule holder at the tip is no longer detached.

When setting it in the main body of Wiz2, insert it with the metal fittings facing down.

How to use Wiz 2 (3) How to switch between HIGH and NORMAL mode

Note the red arrow in the video! You will notice that when you press and hold it, it switches between HIGH and NORMAL.

Note that the HIGH mode is selected by default, and when we asked a JT employee why, he said, "Because we want you to try the HIGH mode first!" he said.

How to use Wiz 2 (4) Device lock and unlock

Wiz 2 does not have power on/off, but has device lock and unlock.

Just click the button three times to lock and unlock it, so when you are done with your smoke, click it three times before moving on.

How to use Whiz 2 (5) How to check remaining battery level and remaining number of suction cycles

The remaining battery level and the number of remaining suctions are all shown on the display, and can be checked by displaying the display.

When the display is off, you can click the button once to make it appear again for about 6 seconds.

How to use Wiz 2 (6) Tobacco capsule exchange

When it is time to replace the cigarette capsule, the "Cigarette Capsule Replacement Notification" appears on the display.

When this display appears, follow the instructions and press and hold for 2 seconds to reset the puff count.

How to use Wiz2 (7) Cartridge replacement

Since the Wiz 2 cartridge contains only enough liquid for five cigarette capsules, the cartridge is replaced when the user has finished smoking five cigarette capsules.

To replace the cartridge, open the bottom opening and remove the cartridge as you did when you set it in place.

Wiz 2 Troubleshooting (how to deal with problems and malfunctions)

A quick look at the areas of concern

The Wiz 2 is reasonably priced at 1,980 yen, but it is a precision machine with a display and heating functions.

If used incorrectly, they can break, and in some cases, initial defects can occur.

This section explains how to respond to such problems and malfunctions. Please refer to this section when you suspect a problem or malfunction, such as when Wiz2 is behaving strangely....

with2 Flow in case of trouble

Wiz 2 Troubleshooting (how to deal with problems and malfunctions)
with2 Flow in case of trouble
  • STEP01
    Check and try out how to deal with each problem.
  • STEP02
    Reset the device
  • STEP03
    Contact Customer Center and request repair or replacement under product warranty

Basically, try to practice how to respond to each problem, and if that does not work, reset the device.

We, the general users, can only do so much,If trying to reset the device does not cure the problem, contact the Customer Center to request repair or replacement under the product warranty.

How to Reset Wiz 2

How to obtain a Wiz 2 product warranty

with2 Malfunctions or failures during charging

Trouble details(i):Cannot charge, ,Charging never ends., ,LEDs do not glow., ,Display does not appear

Trouble ①: Cannot charge, charging never finishes, LED does not light up, display does not turn on

Normal operation of Wiz 2 when charging
LED flashes
The display shows an icon indicating that the battery is being charged.
Vibration when USB cable is plugged in
Charging takes about 60 minutes.

The above is normal operation when charging, but when these do not work, there may be some malfunction or failure.

Troubleshooting when charging does not work properly

  1. Use the AC adapter and USB cable included in the starter kit
  2. AC adapter plugged directly into a wall outlet (not charged from an octopus or computer)
  3. Check AC adapter and USB cable for dirt.
  4. Check if the device temperature is too hot or too cold

Most cases of not being able to charge properly are caused by not using a genuine AC adapter or cable.

Also, devices cannot be charged if they are too hot, for example, if they are left in a car, so in such cases, wait until the device returns to normal temperature before charging.

About the proper temperature for Wiz 2
When charging
5 to 35 degrees Celsius
when usingTemperature: -5 to 40 degrees Celsius

with2 Malfunctions and failures during use

Trouble details(2):The battery runs out of charge immediately after charging.

Trouble ②: Battery drains immediately despite being charged

Normal operation of Wiz 2 when used
Battery capacity for 5 cigarette capsules

The battery is originally designed to hold enough power to smoke "five cigarette capsules," but it runs out of charge quickly, among other problems.

When the battery runs out of charge quickly after charging.Troubleshooting

  1. Suspect age-related deterioration (battery deteriorates and capacity decreases with time of use)
  2. Check device temperature

After one year of use, the battery will deteriorate, in which case it is not a malfunction but a "life expectancy" and should be considered for replacement.

However, if you have been using it for only one or two months, you may suspect a malfunction, so try resetting it, and if that does not work, contact Customer Center.

In addition,If the device is cold, e.g. in winter, it may quickly run out of battery powerIn such a case, try recharging the battery after bringing it back to room temperature.


Trouble details(iii):No vapor is produced when inhaled.

Trouble ③: No vapor is produced when inhaling

Normal operation of Wiz 2 when used
・Vapors are generated when aspirated.

When Whiz2 is normal, it produces vapor when inhaled, but sometimes no vapor is produced when inhaled. If this happens, please check the following correspondence.

When no vapor is produced when you inhale.Troubleshooting

  1. Make sure the air intake (side window) is not blocked by fingers.
  2. Make sure it is not locked.
  3. Check to see if a cigarette capsule replacement notice is displayed.
  4. Check to see if the battery is still charged.
  5. Checking and replacing the amount of liquid remaining in the cartridge

In most cases, it is due to a confirmation error, but sometimes steam is not generated even though there are no problems with all the correspondence methods.

If this is the case, contact the Customer Center, as there is a high possibility of malfunction.


Trouble details4):Display does not appear, LEDs do not light up

Trouble ④: Display does not turn on, LED does not light up

Normal operation of Wiz 2 when used
Press the button once to display
LED glows when button is pressed once (backlight)

Under normal conditions, a single press of the button will bring up the display and the LED on the side will light up, but if this is not the case, there is a high possibility of a malfunction.

Display does not appear, LEDs do not light upo'clock (i.e. the first day of the rat of the New Year)Troubleshooting

  1. I'll check the charge.
  2. Attempt to reset
  3. Contact Customer Center

If the battery is simply out of charge, there is no problem, but if you are sure that the battery is fully charged, but the display and LEDs are still malfunctioning, there is nothing you can do except try to reset the battery.

However, this is not a symptom that can be cured by resetting, so it is a problem that should be immediately reported to the Customer Center.

with2 Other malfunctions and failures

Trouble details(5) ⑤:Cartridge insert cover does not close

Trouble ⑤: Cartridge slot cover will not close

Normal operation of Wiz 2 when used
Cartridge insert cover closes properly.

The most fragile part of the Wiz2 is the cartridge insert cover, which can be difficult to use if broken, so use it with care.

When the cartridge insert cover does not closeTroubleshooting

  1. Make sure you inserted the cartridge in the correct orientation
  2. Check the cartridge insertion area to make sure it is not clogged with dust or other debris.
  3. Check cartridge insert cover for damage.

The cartridge insert cover of the Wiz 2 is a flip-type cover that is held in place by a fingernail, so it is a part that may well be damaged over time.

If the product is dropped or otherwise damaged, "it is not covered by the product warranty."So, be very careful when handling them.


Trouble details6): When I try to use it after a long time, it doesn't work when I press the button.

Trouble ⑥: Device does not respond when pressing the button after not using it for a long time

Normal operation of Wiz 2 when used
Press the button to display

A light press of the button once will normally show the display and unlock the device for use, but if the device is not used for a long period of time, the voltage in the battery may drop and the device may not work.

I haven't tried to use it in a while and it doesn't work when I press the button.o'clock (i.e. the first day of the rat of the New Year)Troubleshooting

  1. Charge the battery once and try again.

This is not limited to the Wiz 2, but applies to any household appliance,If the battery is not used for a long period of time, the voltage will drop and it will no longer be usable.So, let's recharge the battery once first.


Trouble details(7): The device is so hot that it cannot be held.

Trouble ⑦: Device becomes too hot to hold

Normal operation of Wiz 2 when used
...never feel hot to the touch.

Naturally, it is used in the hand, so it does not usually feel hot.

Device is too hot to hold.o'clock (i.e. the first day of the rat of the New Year)Troubleshooting

  1. Try to remember if you are not using it continuously
  2. Stop using it immediately and contact Customer Center.

Please be assured that an increase in device temperature due to continuous use is not a malfunction.

When a device is so hot that you cannot hold it, even though you are not using it continuously, it is dangerous.Therefore, stop using it immediately and ask Customer Center for instructions.

Wiz 2 Reset Method

A quick look at the areas of concern

Resetting the Wiz 2 is easy, just press and hold the button to charge the battery. Resetting will return the internal settings to the improved shipping state.

Reset method: Insert the USB cable while pressing the button (to charge the battery)

Normal charging operation... vibrates once and then starts charging.
Operation at reset...After vibrating for 1 secondand vibrates once again to start charging.

When you look at the display, charging starts normally, so you may think, "Huh?" You may think, "What?", but when you insert the USB cable, if it vibrates for a long time with a "boo" sound, the reset is complete.

Don't forget, the key is to hold down the button!

Wiz 2 Product Warranty and Customer Center

A quick look at the areas of concern

Wiz 2 also has a product warranty, but it is not as generous as Plum X's, and is more general in nature, so please treat it with care.

In the heated cigarette community these days, it's commonplace to have a very generous warranty that covers even self-loss or loss,If you think it is the same content, you may be rejected, saying that it is not covered.

Wiz 2 Product Warranty Coverage

Wiz 2 Product Warranty Coverage

The Wiz 2 comes with a product warranty, which covers initial defects and spontaneous failures under the following terms

with2 Warranty

Period12 months from purchase
subject (of taxation, etc.)Wiz2 main unit, AC adapter, USB cable
ContentsOnly natural breakdowns
termsWarranty: Must have a warranty card.

Without a warranty card or proof of purchase (receipt or receipt), minor "scratches" will not be covered.

Similarly, despite the correct use ofCovered only in case of spontaneous failureTherefore,Drops, submersion in water, and loss are also not covered by the warranty.The first two are the following.

Contact information (Customer Center) in the event of a Wiz 2 malfunction.

Phone number:0120-108-513
Office Hours9:00~21:00
supplementExcept for year-end and New Year's holidays

They are available on weekends and holidays, so that is reassuring!

However, it tends to be difficult to reach us on weekends, holidays, and at 12:00 and 18:00 because of heavy traffic, so try to contact us on weekdays as much as possible.

Summary of how to use Wiz 2 and how to prevent problems and malfunctions

Wiz 2 can be equipped with functions such as lock and mode switching, but there are only two button operations, "long press" or "press three times", so it is good to remember them!

Also, there will be times when cases of suspected problems or malfunctions will occur, but just remember how to reset the system and the contact information for the Customer Center.

Comment

en_USEnglish
Moclog is a blog about tobacco.
You are over 20 years old, correct?
No, sir.
🌐 English