⚡ 【早見表】VAPEメカニカルMOD(メカモッド)の安全ルールとテクニカルMODとの違い
| メカニカルMODとは? | 基板(保護回路・制御チップ)を持たず、バッテリーの電力をそのままコイルへ直結通電させる上級者向けのVAPEデバイスです。 |
|---|---|
| 絶対に守るべき3大安全ルール | ①オームの法則に基づく適正抵抗値のビルド、②被膜破れのない高品質な IMR/INR バッテリーの使用、③ハイブリッド接続時のポジティブピン突出確認が必須です。 |
| 初心者は必ずテクニカルMODから | 短絡(ショート)防止や過放電保護が入った「テクニカルMOD(iStick Pico等)」やポッド型VAPEであれば、初心者でも安全に爆煙を楽しめます。 |
📌 あわせて読みたい関連データ・最新記事
- What is a mechanical mod?
- What kind of structure is primitive?
- What in the world is advanced?
- There's more................notes
- Why are we attracted to mechanicals in spite of all this hard work?
- For comrades who are about to make their mechanical debut
- Experience as a prerequisite for mechanical mod debut
- What I thought when I made my debut as a mechanical mod.
- Let me end with an important story.
- postscript
What is a mechanical mod?
ちょっと本格的なVAPEになると、バッテリーMODとアトマイザーが別々になってますよね。 このバッテリーMODには2種類あって、It is equipped with an electronic control board.technicalThere are mods and mechanical mods that don't have any of those things.んです。 初心者にオススメと言われる”iStick pico(ピコ)”なんかはテクニカルMODの代表例でして、出力が変えられたり温度管理機能がついていたりと高性能。 それに対してメカニカルMODは原始的で、電池(バッテリー)のパワーをそのままアトマイザーに伝えるだけなので、これと言った機能は一切ありません。 この例えが正しいかどうかはわかりませんが、今の電車をテクニカルMODとするならば、メカニカルMODは蒸気機関車みたいな感じ。What kind of structure is primitive?
テクニカルMODとの一番の違いは、電池に直接アトマイザーを接続する点にあります。
テクニカルMODには、アトマイザーとの接続部分にピンがあるんですが見えますか?
これがあることで安全に接続できるようになっているのですが、メカニカルMODは穴が開いてるだけ。
この穴にアトマイザーを差込み、The structure of a mechanical mod is to have it connected directly to the positive terminal of the batteryIt is.
What in the world is advanced?
先程の説明だけだと、「ふーん、バッテリーに直接繋ぐのがメカニカルね」・・・で? となりかねないので、本題はここから。 The mechanical mod.For advanced users(in Japanese history)hazardous(Reason for being)We will explain the following.Reason #1: No safety devices at all.
見ての通り、メカニカルMODはほとんどが”ただの金属製の筒”です。
ボタンもパフボタンが1つあるだけで、めちゃくちゃシンプルな構造ですよね。
電子制御板なんてついてないので、There are no features called "safety devices" at all.んです。
テクニカルMODだと、ショートしたり抵抗値が低すぎたりすると安全装置が働いて停止してくれるんですが、メカニカルMODはショートしようがヤバイ抵抗値だろうがそのまま電気が流れてしまうので、There is a risk of the battery exploding if something goes wrong.んです。
バッテリーが爆発して大怪我した・・・なんて画像を見ましたが、グロすぎてビビりました。
Reason #2: Not knowing Ohm's Law is dangerous.
I don't think you have to think that much about it with technical mods,In the mechanical mod.Ohm's lawis required。
なぜかと言うと、バッテリーに直接接続するので、調整なしでそのバッテリーの持つパワーがアトマイザーに流れるワケですよ。
ですので、The coil must be wound after calculating the operational resistance based on the specifications of the battery to be used.んです。
例えば、3.7V(最大電圧4.2V) / 20Aのバッテリーに抵抗値0.1Ωのアトマイザーを接続すると、「4.2V ÷ 0.1Ω = 42A」と計算できます。
このバッテリーの電流は20Aなので、倍以上の電流が流れることになります。
この状態で使用すると、バッテリーに負荷が掛かり爆発する可能性が・・・オームの法則って大事でしょ?。
Reason #3: There are rules that must be followed.
It's not that difficult,We absolutely must protect them.ruleがあります。
それは一連の手順を守る、ということです。
1.atomizerPrepare a (build(Already)
2. Connect the atomizer to the mechanical mod.
3. Put the positive pole on the atomizer side.batteryinsert
Tighten the lid.
To add,When changing atomizers, the battery must be disconnected, and when carrying the atomizer, the battery must be disconnected, which is the basic rule and must be followed absolutely.です。
なぜかと言うと、アトマイザーがついていない状態でバッテリーを入れてしまうと、場合によってはショートしちゃうんです。
ショート=爆発の可能性ですから、このルールは自分のためにも絶対に守らないといけません。
移動するときにバッテリーを抜くのも同様の理由です。
*By the way, do not carry the battery naked, but carry it in a case.
There's more................notes
書けば書くほど面倒臭いものに感じちゃうと思うんですが、実はまだ注意点がいくつかあるんです。 後半には「これならデビューできる!」と思えるヒントを書いていますので、もう少しお付き合いください。 もうね、Mechanical mods are delicate children.I'm just sweating.Note #1: Atomizers should be chosen
For now, what I want you to memorize memorably is,."clearomizerI don't use the "*."まずコレ。
理由は簡単でポジティブピンが出っ張ってないので、バッテリーにちゃんと接続できずショートしちゃうんです。
同じ理由で、RDAなどのビルド用のアトマイザーであっても、ポジティブピンが引っ込んでいるのは使わないほうが良いです。
中にはネジ式でポジティブピンの長さを調整できるものもありますが、Atomizers to be connected to mechanical mods, check the positive pin carefully.The following is a list of the most important factors that need to be taken into account when making a purchase.
Note #2: You should also choose a battery.
Batteries for vape are,flat-topのlithium ionUsing batteries is normal.です。
バッテリー選びも重要ですが、最低ラインVAPE用のバッテリーを買ったとして、次に大事なのがInformation on the battery。
私のバッテリーは「EFest IMR 18650 3000mAh 35A 3.7V(ただし連続放電は20Aと記載)」、この情報からオームの法則で計算するワケですね。
バッテリーは満充電時4.2Vまで出るので最大値で計算、また電圧は連続放電をベースに計算します。
「4.2V ÷ 20A = 0.21Ω」と計算できました。
これが、理論上このバッテリーのギリギリOKラインになりますが、ピッタリでは安全とは言えませんので最低でもプラス0.1Ω以上は高めにコイルを巻きましょう。
また、Different batteries have different capacities (3000mAh), current ratings (35A) and voltages (3.7V)So, the choice of battery is very important.
Note #3: Batteries should be checked frequently.
バッテリーには皮膜と言って、全体を覆っているフィルムのようなものがあります。
この被膜の内側はすべてマイナス極になっているため、filmIt is extremely dangerous to use a battery that has been torn open and the inside is visible!。
まあ簡単に言うと、破けたまま使うとショートするってことです、マジで危ないのでお忘れなく。
もう1つ、バッテリーのプラス極もチェックして欲しいポイントです。
長く使っていると、ポジティブピンに押されてか凹んじゃうことがあるんですよ。
そんな状態のバッテリーを使うと、やっぱりショートする危険性がありますので、It is very important to check the batteryIt is.
Why are we attracted to mechanicals in spite of all this hard work?
ここまで飛ばさずに読んだ方であれば、「もう面倒だからピコでいいっす」・・・って人もいるでしょう。 実際、機能だけで言ったらテクニカルMODのほうが断然優れてますし、金額的にも安く済むことが多いです。- Knowledge of vape required
- There are rules for using it.
- There are detailed precautions.
- The unit is also very expensive.
Attraction #1: It's just so cool!
Mechanical mods, while simple in construction, may have artistic designs or be a rare species called high-end.
mass production(mass-produced products), there's a coolness that you can't experience.んですよね。
正直お値段はそれなりにしますが、There's a kind of magic that satisfies the buyer's desire for things.んだと思います。
私も今回のメカニカル・デビューで開封した「VGOD」なんかは、当時「カッコいい!」という理由だけで買いましたからね、カッコいいは正義なんです。
Attraction #2: I want to climb the stairs to adulthood!
That's just my story, but as a vape enthusiast, for now.I wanted to use a mechanical mod that is considered to be for advanced users.んですよ。
別に誰かに認められたいワケでもないし、認めてくれるワケでもないんですが、自分でそういうゴールを設定していた感があります。
結局は自己満なんですけどね、戦国無双で言うなら「普通モード」ではなく敢えて「地獄モード」でクリアしたい・・・そんな感じです。
ただし、これだけはお伝えしておきますが、Just because you use a mechanical mod doesn't make you great or amazing.ので、いつか必ずメカニカルを使わないといけないなんてことは全くありません。
VAPEは自己満で楽しむものだと思いますので、自分が使いたいものを堂々と使えばいいんです、私はそれがメカニカルだっただけという話です。
Attractiveness #3: Almost unbreakable, so it can be used for a long time.
This is one of the few advantages of mechanical mods, though,Super-simple construction, free from mechanical breakdownsです。
逆に、テクニカルMODには基盤が組み込まれているため、ここが壊れたらどうにもなりません。
バッテリーも交換式なので、Mechanical mods can be used semi-permanently as long as they are well cared for.んです。
まあパッと見た感じ、ただの金属製の筒ですからね、壊れようがないんですよ。
For comrades who are about to make their mechanical debut
For those of you who are thinking, "Oh, come on, give me a quick tip!" For those of you who want to know...This could be my debut!" How to thinkをご紹介します。 もちろん、このエントリーに書いてあるルールや注意事項は守ってもらわないといけませんが、ある意味、変なところで悩む必要はなくなると思いますので参考にどうぞ。 私も最初はめちゃくちゃ悩みましたからねー、少しでもお役に立てれば幸いです。Tip #1: Batteries are available at vape stores.
メカニカル・デビューするときに一番悩むのがバッテリー。
フラットトップにIMR?意味わからんっ!って人もいますよね。
しかも、安さだけを求めると粗悪品(皮膜を巻き直して中身は低級品を売りつけるなど)も出回ったりしているので、何を買えばいいのかわからなくなります。
そんなときにオススメなのがTo buy from a vape store.です。
VAPEショップですから、VAPE専用バッテリーしか売ってませんので絶対にハズすことがありません。
私の経験上、楽天なら「Flavor Kitchen..."office edgeMr.," the rest is "VAPE STEEZ」さんあたりは間違いありません。
Amazonに安いバッテリーが沢山掲載されていますが、先程お伝えしたようなリスクもあるので、I recommend you to buy it from a vape store base until you get used to it!.
Tip #2: Build at 0.5 ohm for now.
Sorry for the very crude tip, but when you build the coils,For now, set 0.5Ω as a guide.することをオススメします。
理由は簡単で、0.5 ohm is acceptable in every battery I know of.It is.
4.2V ÷ 0.5Ω = 8.4A
VAPEで使用されるバッテリーの多くは20A~40Aくらいが主流で、10Aを下回るものは18650では見たことがありません。
仮に15Aのバッテリーであっても、電流は8.4Aなので十分余裕があります。
ちなみに今回の私のセッティングは0.5Ωを目指して0.47Ω、これでも十分に爆煙を楽しめますよ。
Tip #3: Buy a set of atomizers if possible.
For example, a VGOD mod is a VGOD atomizer, and so on,I'll buy a set for now.とリスクが減ります。
アトマイザーをセットしたときの一体感も素敵ですが、それ以上に冒頭書いたようなポジティブピンの心配がちょっと減ります。
というのも、クリアロはもちろんNGですが、Some build atomizers, such as RDAs, are not suitable for hybrid connection (i.e., connection to a mechanical mod)んです。
バッテリー同様にアトマイザーも安全を確保する上で重要なパーツなので、慣れるまではセット物を使うのが安心ですよ。