Smoking area near here

Plume x blinking fast? Explanation of all patterns of blinking. Summary of what the flashing patterns mean and what to do about it.

Ploom X Blinking Fast?! All Blinking Patterns Explained with Videos: Summary of Meanings and Solutions Ploom
Ploom PloomX Review PloomX980 yen PloomX Mobius PloomX Camel PloomX CouponIncluding PR

Article content updated: 2026-09-23 | Information checked: 2026-09-23

Check First: Ploom X Blinking Meanings Differ Depending on the LED Location

According to the official FAQ, blinking of the lower LED indicates a low battery level. If all LEDs continue to blink, try resetting the device; if that does not resolve the issue, temperature protection may be active, so return the device to a normal temperature environment and check again. Do not assume a malfunction based solely on the number of blinks, and be careful not to mix up the instructions for Ploom X and X ADVANCED.

JT Official: Ploom X Lamp Blinking FAQ // Troubleshooting Guide by Model

Official FAQ Verified: 2026/9/23

Good evening,Heated cigarette blogger Genki (@MOQLOG_JP)It is.

Plume X users can now be seen in smoking areas near our offices, and many of them may have switched to Plume X at the right time, such as when the price was raised.

However,You'll be surprised when you start using it,Plume XLEDs like you've never seen before in your life.fast flashingWhen we started the

Oh no, it's broken! Before you panic, you should know what the flashing light means and what you can do about it.

Also,In this article.All Plume-X flashing and lighting patternsand necessary for restoration.Reset method, ,Customer Center in case of breakdownInformation on the following is also included for your convenience.

so much (little)school (e.g. of ikebana)I want to remember!
  • Be sure to remember thatOnly when the entire LED is blinking fastOK in.
  • Reset devices in various situationsSo, it is good to remember.
  • Plume X has a generous warranty in case of malfunction or failure.Be sure to register your product!.

What is the condition of Plume X blinking fast?

What does it mean when Plume-X blinks too fast? Please see two patterns first.

Only the bottom part of the LED flashes

This means the battery is low, so it is not a malfunction.

approachCharge the device.

→How to charge Plume-X

The problem is the next LED total blinking pattern.

All LEDs blinking

This may be due to some defect (malfunction) in the Plume X itself.

approachThe device must be reset or the device must be brought back to the proper temperature.

→How to reset Plume-X

Meaning that only the lower part of the LED of Plume X is blinking.

As mentioned earlier, only the lower part of the LED on the Plume-X is blinking, which means that the battery level is low.

Please check the meaning of each blinking pattern, as they have slightly different meanings.

Plume X Flashing Patternsmeaningcondition
Only the lower part of the LED flashes 3 times slowlyLow battery conditionI can smoke one or two.
Only the lower part of the LED flashes 4 times at high speedNo battery power remainingI can't smoke one.

In any case,Blinking lower part of LED is not a malfunctionThe battery can be recharged and can be used again.

→How to charge Plume X

Meaning of the entire LED of Plume X flashing at high speed

Be careful when the entire Plume-X LED is blinking at high speed.

It mainly means defects and breakdowns, though,The number of times it blinks at high speed will tell you what kind of defect it is.

Plume X Flashing Patternsmeaningcondition
Whole LED flashes 9 times at high speedAbnormal device temperatureIf the Plume-X body is too hot or too cold
The entire LED continues to flash at high speed for a certain period of timeThere is a big possibility that the device is malfunctioning in some way.There is some abnormality in the Plume-X itself.

In case of temperature abnormality, if the Plume-X is hot, just wait for it to cool down, or if it is too cold, warm it up to human skin, etc., and it will be ready to use when it returns to the proper temperature.

Proper temperature for Plume-X
  • during operation (e.g. of a machine, equipment, etc.)Between 5 and 35 degrees Celsius.
  • When chargingBetween 5 and 35 degrees Celsius.
  • In StorageBetween -10 and 45 degrees

If the LED blinks more than 9 times, it is likely that there is some kind of problem with the device, but it can be recovered by resetting Plume-X, so try resetting it first.

→How to reset Plume X

What to do when only the lower part of the LED of Plume X blinks (how to charge)

How to charge Plume-X
  • STEP01
    Check the USB cable socket on the bottom of the Plume-X unit.
    Check the USB cable socket on the bottom of the Plume-X unit.
  • STEP02
    Take out the Type-C cable included in the starter kit.
    Take out the Type-C cable included in the starter kit.
  • STEP03
    Insert the Type-C cable into the USB cable slot of the Plume-X and you're done!

The AC adapter is sold separately from Plume-X, but there is no need to buy one.

A standard AC adapter will work fine, so please connect the included Type-C cable to your AC adapter to charge the battery. (5V1.5A recommended)

During charging, the lower part of the LED starts blinking and extends to the top depending on the state of charge, and the battery is fully charged in approximately 140 minutes.

AC adapter standards that can be used

Any product equivalent to an AC adapter with the following standards can be used.
Rated input: 100 VAC-240 VAC, 50/60 Hz, 0.2 A
Rated output is DC5V, 1.5A
Complies with IEC60950-1, IEC62368-1 and PSE standards

What to do if Plume X does not charge

If it is charging properly, the LED on the Plume-X will blink slowly, but when it does not blink, it is not charging.

It may not be a glitch, so please check the following information.

What to do when Plume-X won't charge
  1. Charge the battery with the genuine Type-C cable included in the starter kit.
  2. If charging with the genuine cable does not workReset Plume-XI will try to do so.
  3. If the battery does not charge even after resetting, call the Customer Center because the unit may be malfunctioning.

If the product cannot be recovered and is found to be faulty after contacting the Customer Center, it will be replaced free of charge within the warranty period.

Also, device registration extends the warranty period, so if you have not yet registered your device, please do so as soon as possible.

→Plume-X Product Warranty

What to do when the entire LED of Plume X blinks at high speed (reset method)

How to reset Plume-X
  • STEP01
    Removing the Plume-X front panel
    Removing the Plume-X front panel
  • STEP02
    Press the button in the center of the device with a pointed tip (e.g., ballpoint pen)
    Press the button in the center of the device with a pointed tip (e.g., ballpoint pen)
  • STEP03
    Press and hold for approximately 5 seconds. When the LED flashes with vibration, the reset is complete.
    The time you are pressing is set to double speed, but in reality you are holding it down for a little over 5 seconds.

If the entire LED of Plume-X is blinking fast,If the temperature abnormality is not the cause, try "reset" first.

In most cases, resetting the Plume-X will resolve the problem, unless it is a fatal failure.

If this does not fix the problem, contact the Customer Center.

→Customer Center Contact Information

Plume X LED Flashing/Lighting Patterns List

Plume-X tells you the various states of the device by flashing and lighting LEDs that show through the front panel.

You don't have to remember anything in particular, but knowing the blinking and lighting patterns will help you notice, "This blinking is OK! I will introduce them all in one step, as well as a review of them.

Plume X LED Flashing/Lighting Patterns List
  • Slide cover open/closed...Lights up according to the remaining battery level
  • Tobacco sticks being heatedSlowly blinks and lights up when heating is complete.
  • while smoking... slowly decreasing with all lights on.
  • At the end of smoking...Flashes on and then off.
  • Charging...Slowly blinking and gradually increasing.
  • Temperature Anomaly... Early blinking (9 times)
  • Defects occurredFast blinking (for a certain period of time)
  • Reset Complete... Fast flashing
  • Bluetooth connection...Flashing up and down

Meaning of LED lighting when slide cover is opened/closed

When the slide is opened, the LED flashes according to the battery level at that time.

When the battery is fully charged, all lights are lit, and when the charge is low, the portion lit decreases to half or one-quarter.

Meaning of LED lighting when slide is opened and closedDisplays remaining battery charge.

  • All lights on... Battery remaining 80% to 100%
  • Half lit... Battery power remaining 20% to 80%
  • Flashes 3 times... I can only smoke about one or two more.
  • High speed flashing... I can't smoke. Please charge.

Meaning of LED flashing during heating of tobacco sticks

Fast forward to the part being heated.

Press and hold the heating button for about 1 second to start heating, and the LED will start blinking at the same time as the vibration.

Heating time is 25 seconds, and the LED flashing gradually increases, and when heating is complete, the LED oscillates twice before turning fully lit.

Meaning of blinking during heating of tobacco stick... Displays the progress until heating is completed.

  • Slowly flashes for 25 seconds while heatingThe company will be
  • From flashing when heating is completeTurns on..

Meaning of LED lighting during smoking

Plume-X is designed to be smokable for 5 minutes instead of the number of puffs, and the LED remains on until the last 20 seconds.

As the remaining time decreases, the number of lit areas decreases.

Meaning of LED lighting during smoking・・・・Indicates smoking hours

  • Smoking hoursschool (e.g. of ikebana)Regardless of the number of puffs.5 min..
  • Slowly until you have 20 seconds left.The number of lit areas is decreasing..

Meaning of LED flashing at the end of smoking

Fast forward to the part being heated.

When 20 seconds remain, it changes to a slow blinking with vibration. (In the video, it is fast-forwarding.)

When the smokable time is over, the LED will vibrate twice and simultaneously turn off all lights.

Meaning of LED flashing at the end of smoking・・・・Indicates that 20 seconds of smoking time is remaining.

  • 20 seconds remainingchanges from lighting to slow blinking when the
  • When smoking hours are over.All LEDs are turned offDo.

Meaning of blinking LED during charging

When the battery is successfully charged, the LED flashes slowly.

The LED flashing portion increases according to the state of charge, and when the battery is fully charged, the LED flashes twice before turning off.

Meaning of blinking LED during charging... Displays the charge status.

  • Approx. 140 minutes to full chargeIt will take.
  • When fully chargedLED blinks twice and then turns offDo.

Meaning of high speed blinking of all LEDs in case of temperature abnormality

It was pretty cold (sweat).

To review, if the LED blinks all 9 times at high speed, it is not a malfunction, as it indicates an abnormal temperature of the device.

※当時筆者は冷凍庫や暖房器具を試してしまいましたが、急激な温度変化は内部結露・基板ショート・バッテリー劣化を招くため絶対に行わず、常温の室内で自然に温度が戻るのを待ってください。

Meaning of high speed blinking of all LEDs in case of temperature abnormalityPlume-X indicates that the temperature is outside the proper range.

  • To use5 degrees Celsius to 35 degrees CelsiusOtherwise, it cannot be used.
  • It's not a malfunction.So, please respond calmly.

Meaning of fast blinking of all LEDs in the event of a malfunction

My Plume-X is sturdy or not easily broken, so I couldn't get a video, but think of it as a temperature anomaly fast blinking for a certain amount of time, not ending at 9 times.

When the Plume-X starts blinking at high speeds like this, the Plume-X will start blinking at the same rate as the Plume-X I mentioned earlier.Reset deviceTry the following first.

If resetting does not restore the system,Customer CenterContact the

Meaning of fast blinking of all LEDs in the event of a malfunction...Indicates that Plume-X is malfunctioning or has failed.

  • When all LEDs flash at high speed,First try resetting the device.
  • If resetting the device does not restore it, it is most likely malfunctioning.because of ...Customer CenterContact the

Meaning of fast blinking of all LEDs upon completion of reset

One blinking pattern to remember is the "fast blinking" of all LEDs when a reset is completed.

This literally means that the reset is complete. After this flashing pattern, please try to reattach the front panel and see if the problem can be fixed and used normally.

Meaning of fast blinking of all LEDs upon completion of reset... Displaying the completion of resetting

  • Reset isPointed tip(ballpoint pen is acceptable). (Ballpoint pens are acceptable)
  • Press and hold for less than 2 secondsThen it is reset.

LED flashes up and down during Bluetooth connection (pairing)

The LED is blinking up and down, which does not indicate a malfunction but rather a standby state when connecting via Bluetooth.

Pairing standby is achieved by pressing the button area four times (the last being a long press) to get this blinking pattern.

Meaning of LED up/down blinking when connected via BluetoothPairing standby status is indicated.

Bluetooth connection (standby state)
→ Press the button area for 1 second x 3 times,Press and hold for 3 seconds on the 4th

How to connect Plume x via Bluetooth! Thorough explanation of what you can do and how to do it! People who can't connect [must see]!

When the blinking LED is hard to see

The LEDs convey various information about Plume-X, but the light is weak and difficult to see! Some people may think that it is difficult to see the LEDs.

Since it represents important information about the device, it cannot be overlooked.

If you have difficulty seeing the LEDs, you can adjust the intensity of the light..

Intensify the intensity of Plume-X LED light.
  1. Open the slide and press the heating button. (You can do this without a tobacco stick)
  2. The light can be adjusted by pressing the heating button during heating.

Useful information in case of malfunctions or breakdowns

While there is nothing wrong with Plume-X, it is a precision machine, so it is impossible to predict what will cause it to break down and when.

In such cases, please review the following four pieces of information that are useful for you to know.

Contact customer center in case of malfunction

Ploom Customer Center

Resetting the device is a first aid measure we can take, but if this does not fix the problem, we are out of luck.

In such cases, contact the Customer Center.

We are available by phone until late, or if you don't want to call, we can email or chat with you.

Ploom Customer Center

The warranty period can be extended with device registration!

Ploom X CLUB (Device Registration)

If Plume-X breaks, they will replace it with a new one within the warranty period, and the longer the warranty period, the better.

Originally, the warranty period was 1.5 years, the longest in the industry, but by registering your device, you not only extend the warranty period to 2 years, but you also get a bunch of other great benefits.

Take this opportunity to register your device and consider joining the Plumex Club.

Warranty Period
  • The product comes with a 1 year and 6 month warranty period at the time of purchase. (Proof of purchase required)
  • Registering a device adds 6 months andExtended to 2 yearsThe following is a summary of the results of the study.
  • By registering the deviceAutomatic enrollment in Plumex ClubCan be done.

Join the Pruex Club and save a lot!

Value Perks of Ploom X CLUB

You are automatically enrolled in the Plumex Club by registering your device, though,Not only does it extend the warranty period, but it also offers a number of special benefits!

The following benefits will be granted upon enrollment, please check the details first.

Plumex Club Membership Benefits
  • Plume-X's Bluetooth connectivity is released.
  • One-time free replacement if device is self-inflicted or lostThey do.
  • Personalized imprinting services are available at Ploom stores nationwide.
  • Receive one free drink at the Ploom store attached to the cafe.
  • You will receive 500 LINE Points the day after you enroll.

Normally, product warranties only cover initial defects and natural malfunctions, but Plumex Club members can also take care of self-inflicted damage (breakage due to carelessness) and loss of products.

Incidentally, when you first join Plumex Club, your status is standard, but as you raise your status by registering pack codes, etc., you will receive additional benefits.

The better guarantee alone is worth the cost of membership, so please consider it!

Plume X Flashing Pattern Summary

This is a much longer summary of all the flashing patterns of Plume-X. Thank you for your patience to the end.

I have written at length, but there are three things I want you to remember from this article.

There are various blinking patterns, but most of them just indicate the status of the device, etc., so just remember that Plume-X is "bad" only when it blinks too fast!

If you think of it that way, there is nothing to worry about.

postscript

As a side note, JT's transfer support discount is a great deal.

Plume-X, which costs 1,980 yen, is now available for 780 yen.So, if you are considering a second unit, this is your chance!

I also bought a second one for my limited front panel and now alternate between silver and black.

New color panels are now available, so why don't you take a look at JT's website if you like?

backspace PR Super value for money! //.

1,980 yen → 780 yen

The sales offer from the time of publication has ended

Ploom X Starter Kit
Ploom X, the next generation heated cigarette device with the new "HEATFLOW®" concept and Nastro design, is a global model that allows unlimited number of smokes for about 5 minutes.
1,980 yen →>780 yen.Opportunities!

The sales offer from the time of publication has ended

Smoking by persons under 20 years of age is prohibited by law.

Plume-X Flashing FAQ

Q
I cannot charge my Plume-X (LED does not blink when charging).
A

There is a possibility of poor connection of the USB connector. Check the connection of the dedicated USB Type C cable again and charge the battery. If you still cannot charge the batteryCustomer CenterContact the

Q
The LED on the Plume-X device (body) is blinking and cannot be heated.
A

When the lower part of the LED on the main unit blinksis the remaining battery power of the main unit is insufficient, please recharge the battery. Please use the dedicated Type-C USB cable and available AC adapter when charging.

When the entire LED of the main unit blinksis a possibility that an abnormality has occurred in the main unit, please reset the main unit. If the LEDs do not stop blinking even after resetting the main unit, a temperature error is detected in the main unit and the safety function is activated. The problem will be resolved when the temperature of the main unit returns to normal, so do not operate the main unit and stand by.

Q
Plume-X device (body) vibrates 5 times and cannot be heated.
A

Abnormal temperature of main unitThe safety function is working by detecting the temperature of the main unit. The problem will be resolved when the temperature of the main unit returns to normal, so do not operate the main unit and stand by.

How Was This Flavor?

Aggregates ratings in 1 click from users aged 20 or older who have actually used the selected brand. By pressing the button, you agree that you are 20 or older and that your response will be used for anonymous aggregation. Response counts are displayed from 5 or more. Options are limited to brands registered in the product master.

1 Did not suit me — 5 Liked it

When you select a brand, the average is displayed if there are 5 or more responses.

Also rate sweetness, menthol, etc.

🛠 この診断・公式リセット手順で症状は解決しましたか?

手順ごとの解決状況を匿名で集計し、機種別サポートDBの改善に活用しています。改善しない場合は無理な分解や冷却を行わず、各メーカー公式窓口へご相談ください。

Comment

en_USEnglish
Moclog is a blog about tobacco.
You are over 20 years old, correct?
No, sir.
🌐 English