Smoking area near here

How to replace the battery in the Icos 3 Multi! I will explain the precautions and tips I noticed when I actually did it.

[Teardown] How to Replace the IQOS 3 MULTI Battery! Tips and Precautions Learned from Hands-On Experience. IQOS
IQOS IQOS Irma Difference IQOS Recycling Oasis Pearl Irma One 1980 yen Ruby MentholIncluding PR
⚡ 【早見表】旧アイコス3マルチのバッテリー劣化と現行「イルマ i ワン」への買い替え比較
自己分解でのバッテリー交換リスク互換バッテリーへの自己交換はハンダ付けや精密分解が必要で、基板ショートや発熱リスクが高くメーカー保証も完全に失効します。
旧ブレード型スティックは販売終了さらに旧IQOS 3マルチ用のマールボロ・ヒーツは全銘柄販売終了しているため、バッテリーを直しても現行スティック(テリア・センティア)は吸えません。
現行の後継一体型「イルマ i ワン」マルチと同じ一体型で20本連続吸引・掃除不要・オートスタート搭載の「IQOS イルマ i ワン」が定価3,980円(税込)で購入できるため買い替えが確実です。

Hello,Heated cigarette blogger Genki (@MOQLOG_JP)It is.

This year finally comes to an end today. Has everyone finished preparing for the year-end and New Year's holidays?

Our family has finished writing New Year's cards, which is a rarity, and all that remains is to buy the groceries.

Now, on the last day of the year 2021, we bring you "Icos 3 MultiThe "Battery replacementのwayI would like to introduce you to the following.

To be frank, there was no news from the companies at the end of this year, and I was thinking about what to do.

Then, I suddenly found a compatible battery for the Icos 3 Multi.

I was going to review it, but then the Irma series was released and I forgot all about it.

We understand that some of you may still be using mulch, and we hope this will be helpful to them.

Please be aware that you are responsible for replacing the battery. We are not responsible for any damage to the battery.

How to replace the battery in the Icos 3 Multi

I had replaced the battery in an Icos 2.4 holder a long time ago, and compared to that, the difficulty level is much lower.

The battery replacement for the multi...

  1. No special tools required
  2. Difficulty level is relatively easy or moderate
  3. The cost is about 1,800 yen.

The sales site is Amazon, and the product page includes simple but easy instructions on how to exchange the product.

However, there are some things I noticed after actually doing it, and I would like to introduce those details today.

What to prepare
  • IQOS 3 MULTI body
  • Compatible Battery (Amazon)
  • Precision screwdriver (-)
  • rubber gloves
  • nippers
  • Thin pins
  • double-sided tape

Compatible battery for Icos 3 Multi

Compatible battery purchased on Amazon

The stock battery capacity is 830 mAh, but the compatible battery is slightly more at 950 mAh.

The key point is that it is already pre-wired. Just plug the black and red cables into the main unit.

No solder is required, and the structure itself is not that complicated, so people who have built plastic models can easily handle it..

Tools are minimal as long as you have a precision screwdriver, so I used a vape build tool.

Battery replacement 1: Pull the base out of the body.

Remove the cap

Sorry the picture is a little dark (sweat)

First, remove the cap.

How to separate the body and internal unit

With a rubber hand, pull out the base part from the body.

With bare hands it was difficult because it was slippery, but it came off easily when I pulled it from both sides with rubber military hands.

Front view with body shell removed

When pulled out, it looks like this.

There is no connection between the body part and anything else, so you can pull it out without worrying.

Back view with body shell removed

This one is the back side where the battery is installed. The steel cover is in the way and the battery cannot be replaced in this state.

The next step is to remove this steel cover.

Battery replacement 2) Remove the steel cover from the base

Side tab section

If you look at the side first, you can see that it is hooked by a nail.

Both sides have these claws, so it is unlikely to come off without doing something about this guy.

Location of the small black pin

The pouch above the CE mark... This one is also on the reverse side, and it seems that you have to pull it out while pressing it.

This was quite troublesome.

Removing the metal cover part

As mentioned on the Amazon sales page, the only way to spread these nails is to force them apart, so use a flat-blade screwdriver x the principle of leverage.

When both the left and right sides have been spread out, pull them out a little at a time while pressing down on the potty.

Disassembled parts

The steel cover was bent a bit, but I was able to remove it anyway.

Note that the spring and the black potty x2 in the upper left corner of the photo will blow out when you pull it out.

I was working inside a shooting box, so I was able to find it easily, but I recommend working in an environment where you can find it even if it flies away, because these pots and springs fly away with great force.

Battery replacement 3: Remove the existing battery

Battery part

Once the steel cover is removed, all that remains is to replace the battery.

Before that, I was concerned about dirt on the blades, so I cleaned all the parts as well.

I am sure you will all want to clean the blades when disassembling them, but please do so with extreme care. Just a little force can snap them off, so please do it gently and slowly! Gently and slowly!

Removing the battery from the tray

At any rate, now that the cleaning is done, we will take out the battery and check the connection surfaces.

Incidentally, be careful not to press the yellow dot near the blade, as this is the power button.

Battery cable terminal connection

The cable is pulled out while spreading this terminal with a pin or similar device.

If you insert the pin several times and spread it out, it will pull out cleanly.

Battery removed

If the terminals can be extended to some extent, the cable can be disconnected with a light tug.

Now it is time to install the compatible battery.

Battery replacement 4: Install a compatible battery

Genuine vs. compatible battery

I just put the compatible battery into the terminal in the same way, but since it is extended, it is loose to plug in as it is (sweat).

You can bend the wires of the compatible battery to make them thicker before inserting it.

Double-sided tape on the back of the battery

It might be a good idea to put double-sided tape on the back of the battery to prevent it from moving.

I stuck it on the stock, so I stuck it on mine as well.

Battery installed

I could have done the same as the original, but the cable for the compatible battery was originally longer, so it would have swelled.

Finally, adjust the sides so that they do not stick out.

How to adjust the battery cable slack

Adjust the slack in the cable on the side by pulling the arrowed part with a screwdriver or the like while inserting it into the terminal.

Now it looks good.

Battery replacement (5) Undo

Precautions when reattaching the metal cover

The most difficult part was here, when installing the steel cover, the spring and potty that easily blow off are too much in the way (sweat).

The trick was to slide it in until it was just barely in place, with only the bottom surface buried, and finally push it in with a finger + flat-blade screwdriver, etc. The third time, it was finally put back in place.

Part that catches on the shell

Once the steel cover is back in place, I just need to put it in the body, but the first part I spread out gets caught and won't fit (sweat).

This could be done by pressing the part against a desk or something to flatten it before doing it.

Sliding back into the body

It was safely stored in the body...it took less than an hour...it's done.

Finally, check the energization. Since there is no heat stick, I can't test it until I actually smoke it, but I will press the button.

Completed and power verified

It may be a little hard to see, but the power supply was successfully turned on.

I'm glad I was able to clean up, just wondering if there was any point in doing this since I've only been using Irma lately... now that I think about it, it's very subtle (sweat).

Icos 3 Multi Battery Replacement Summary

IQOS 3 MULTI and compatible battery

After going through the whole process, I think again that it's pretty easy compared to disassembling other devices.

I thought it was easy to try, requiring few special tools.

The hardest part was removing the steel cover - I had to bend the cover to remove the nails, and the potty would blow off, so that was the hardest part..

I have written about all the things I noticed when I actually replaced the battery, so if you are a multi-lover, please refer to this page.

postscript

This will be the last update for this year, as I play Momotetsu with my children every year at the end of the year.

We would like to thank our readers, as well as manufacturers and distributors, for their support in 2021.

We look forward to working with you in 2022!

Have a Happy New Year!

How Was This Flavor?

Aggregates ratings in 1 click from users aged 20 or older who have actually used the selected brand. By pressing the button, you agree that you are 20 or older and that your response will be used for anonymous aggregation. Response counts are displayed from 5 or more. Options are limited to brands registered in the product master.

1 Did not suit me — 5 Liked it

When you select a brand, the average is displayed if there are 5 or more responses.

Also rate sweetness, menthol, etc.

Comment

en_USEnglish
Moclog is a blog about tobacco.
You are over 20 years old, correct?
No, sir.
🌐 English